DHR 500 C420【PDF 1/4 页】SENSOR CURRENT 500A 50V MOD

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录403

[1页]2页 3页 4页

AC/DC Current Transducer DHR-C420

The transducer for the electronic measurement of DC & distorted AC

waveform currents, with galvanic isolation between the primary circuit

(power) and the secondary circuit (measurement). True RMS 4-20 mA

current output.

Electrical data

I PN = 100 .. 1000 A

Primary Nominal

Primary AC Current

Output current

Type

DC & AC Current

I PN (A.t.RMS)

100

200

300

400

500 2)

600 2)

1000 2)

Max. Peak Value 1)

I P (A)

600

1000

1800

I OUT (mA DC)

4-20

DHR 100 C420

DHR 200 C420

DHR 300 C420

DHR 400 C420

DHR 500 C420

DHR 600 C420

DHR 1000 C420

Features

● VFD and SCR waveforms current

measurement

● True RMS output

● 4-20 mA current output

● Panel mounting

● Eliminates insertion loss

● Isolated plastic case recognized

R L Load resistance

V C Supply voltage

I C Current consumption

I SL Output current limitation

? P Overload capability (Ampere Turns)

Performance data

X Accuracy @ I PN , T A = 25°C (excluding offset)

L Linearity error (1% of I PN .. ± I PN )

I OE Electrical offset current, T A = 25°C

TCI OE Temperature coefficient of I OE ( 0..+60 °C)

(-40..+70 °C)

TCI OUT Temperature coefficient of I OUT (% of reading)

t r Response time to 90 % of I PN step

BW Frequency bandwidth (± 1 dB)

General data

< 300

+ 20 .. 50

30 mA + I OUT

< 25

30000

< ± 1

< ± 1.0

± 3.2

± 6.4

± 0.1

< 150

DC 20..6000

V DC

A.t

% of I PN

m A/K

%/K

according to UL94-V0

Advantages

● Large aperture for cable up to

?32mm

● High isolation between primary

and secondary circuits

● Easy installation

Applications

● VFD Controlled Loads

VFD output indicates how the

motor and attached load are

operating.

● SCR Controlled Loads

Acurate measurement of phase

angle fired or burst fired (time

proportioned) SCRs. Current

T A

T S

IPxx

Surrounding operating temperature

Surrounding storage temperature

Mass

Protection degree

- 40 .. + 70

- 40 .. + 85

260

IP20

°C

measurement gives faster

response than temperature

measurement.

● Switching Power Supplies and

Electronic Ballasts

True RMS sensing is the most

accurate way to measure power

Notes : 1) The Max. Peak AC Current is the highest peak level of the primary

supply or ballast input power.

signal that is taken into account for accurate True RMS calculation. Yet

the device is designed for maximum continuous True RMS value equal to

I PN , whereas the output is limited by the above specified output limitation.

According to the UL 508 Standard for Safety for Industrial Control

Equipment the primary current must not exceed 475 A.t.RMS through the

transducer hole.

Application domain

● Energy and Automation

Page 1/4

100518/20

LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice.

www.lem.com

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式